Please wait a minute...
工程设计学报
Chinese Journal of Engineering Design  2015, Vol. 22 Issue (4): 399-404    DOI: 10.3785/j.issn. 1006-754X.2015.04.015
    
Research and application of finite element method in the design of wave spring
ZHANG Xiao-liang1， LIN Wei-feng2
1.Engineering Department， Johnson Electric， Shenzhen 518000， China;
2.Design Center of Motor Control Department， Johnson Electric， Shenzhen 518000， China
Download: HTML     PDF(2497KB)
Export: BibTeX | EndNote (RIS)      

Abstract  Wave spring is one of the most important parts in the motor for vibration reduction. Perfect wave spring can substantially reduce the vibration of the normal running motor which extends the life of the motor. In order to design the wave spring which met the specifications from customer, finite element analysis method was used to simulate the wave spring pressure process. The characteristic of load-deflection curve was studied and three obvious inflection points were found. The relationship between these three inflection points and the stress diagram and theoretical formula of corresponding compressed wave spring was studied to find out the reason of why inflection points appeared in the load-deflection curve and modified the geometry parameters of wave spring according to the differences between the load-deflection curve and customer's specifications. Finite element analysis would be carried out again according to the new model until the load-deflection curve fitted the customer's specifications. At last, the load-deflection curve of the last model was compared with curve generated by test to identify the reliability of finite element analysis method in the design of wave spring. The experimental results matched very well with the finite element analysis load-deflection curve which proved the effectiveness of the finite element analysis method in the design of wave spring.

Key words： wave spring      vibration reduction      non-linear analysis      load-deflection      optimal design     
Received: 04 May 2015      Published: 28 August 2015
Service
E-mail this article
Add to my bookshelf
Add to citation manager
E-mail Alert
RSS
Articles by authors
Cite this article:

ZHANG Xiao-liang， LIN Wei-feng. Research and application of finite element method in the design of wave spring. Chinese Journal of Engineering Design, 2015, 22(4): 399-404.

URL:

https://www.zjujournals.com/gcsjxb/10.3785/j.issn. 1006-754X.2015.04.015     OR     https://www.zjujournals.com/gcsjxb/Y2015/V22/I4/399


有限元方法在波形弹片设计中的研究与应用

波形弹片是电机减振的重要部件之一，理想的波形弹片可以大大减少电机正常运转过程中的振动，延长电机的寿命.为设计出满足规格的波形弹片，利用有限元分析方法对波形弹片的受压过程进行分析，研究弹片有限元分析所得到的载荷—挠度曲线，发现3个比较明显的拐点，再将这些拐点与对应弹片压缩情况下的应力图以及理论公式联系起来分析，找出拐点产生的原因.并将所得到的载荷—挠度曲线与客户所提供的规格进行对比，然后根据曲线对比产生的差异以及有限元分析曲线的特点，再按理论公式有针对性地修改模型几何参数，对新模型再次进行有限元分析，直至修改的模型计算结果比较理想为止.最后将该理想模型有限元分析的载荷—挠度曲线与试验测试所得的载荷—挠度曲线进行对比，发现两者吻合非常好.这证明了有限元分析方法在波形弹片设计中的可靠性.

关键词： 波形弹片,  减振,  非线性分析,  载荷—挠度,  优化设计 
[1] ZHANG Jin, LIU Pei-shan, YIN Yu-feng. Design and dynamic characteristics analysis of Y-shaped rotary ultrasonic motor[J]. Chinese Journal of Engineering Design, 2021, 28(2): 248-254.
[2] SUN Yue-hai, TANG Er-xing. Optimal design of basic parameters of spiral bevel gears[J]. Chinese Journal of Engineering Design, 2020, 27(5): 616-624.
[3] ZHANG Xiao-liang， LIN Wei-feng. Research and application of finite element method in the design of wave spring[J]. Chinese Journal of Engineering Design, 2015, 22(5): 399-404.
[4] MA Tian-Zheng, QIN Dai-Cheng, ZHANG Yi-Min. Reliability-based optimization of harmonic gears using genetic algorithm[J]. Chinese Journal of Engineering Design, 2011, 18(4): 246-250.
[5] CHENG Xian-Fu. Research on robust optimization design based on axiomatic design and compromise decision support problem[J]. Chinese Journal of Engineering Design, 2008, 15(6): 393-397.
[6] ZHANG Yi-Min, HUANG Xian-Zhen, HE Xiang-Dong, ZHANG Xu-Fang. Optimization design for kinematics accuracy reliability of planar linkage machine with arbitrary distribution parameters[J]. Chinese Journal of Engineering Design, 2007, 14(4): 274-277.
[7] SU Hua-Li, QIN Bao-Jun. Optimal design of heat sinks based on genetic algorithms[J]. Chinese Journal of Engineering Design, 2007, 14(1): 31-34.
[8] ZHAO Yang, JIN Feng. Stability of cylindrical shells with rectangular openings subjected to axial compression[J]. Chinese Journal of Engineering Design, 2004, 11(5): 249-255.
[9] SU Xin-Ping, YAN Xiang-An, ZHANG Cheng-Pu. Analysis on structure vibration of pipelines and study on vibration reduction[J]. Chinese Journal of Engineering Design, 2002, 9(3): 141-143.
[10] XIE Jing-Qing. Design Method of Mechnical Product's Tolerances at Least Manufacture Cost[J]. Chinese Journal of Engineering Design, 2000, 7(4): 51-54.